Search results for: 'tg:echokrys0 top 10 front singl telegram'

VD908  Adjustable mini-loop exit sensor

Specification: 19mm diameter sensor 22m cable length 8-40V dc  or 8-28V ac Iq = 1.6mA, Idetect = 30mA Module size 25 x 39 x 52mm (excl conn) Environmental rating – IP65 1A @ 30Vdc volt free contacts Operating temp -35° C to 74° C

New mini-loop kit with adjustable sensitivity module and new probe 

Learn More

Operator with 24 V motor, featuring a control board with dip-switch settings, on-board radio decoding, movement and obstruction-detection control for sliding gates weighing up to 400 kg that are up to 10-m long

Motor Features: Encoder	Motor Voltage: 24v
Max Length: 10m	Max Weight: 400Kg

 

CAME Connect	European Standards

Learn More

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

Learn More

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

Learn More

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

Learn More

FA.T80   CoBRA programmable beam

Specification: 7 fixed ranges plus full adjustment 10-30V dc   10-24V ac Iq = 65mA, Idetect = 28mA Dimensions 37 x 36 x 108mm Environmental rating – IP65 0.8A @ 30Vdc volt free N/O or N/C Operating temp -10° C to 60° C

Programmable range photobeam, one side only. Set range on DIP switches, or fully adjustable. 

Learn More

FA.T80   CoBRA programmable beam

Specification: 7 fixed ranges plus full adjustment 10-30V dc   10-24V ac Iq = 65mA, Idetect = 28mA Dimensions 37 x 36 x 108mm Environmental rating – IP65 0.8A @ 30Vdc volt free N/O or N/C Operating temp -10° C to 60° C

Programmable range photobeam, one side only. Set range on DIP switches, or fully adjustable. 

Learn More

Pair of surface mounted infrared-beam photocells rated at 12 - 24 V AC - DC. Range: 10 m

Learn More

The VD955 can be used as either a safety loop or free exit probe detector. It should not be used as a safety loop if used with a Free Exit Probe. 

The VD955 includes a VD.CI Interface board, to work with most gate automation control panels.

• 10-30V ac/dc
• Selectable for full loop or exit sensor
• Selectable fail safe (presence) or fail secure (exit)
• 10 sensitivities
• 4 frequencies
• Contact closure/opening time delay

Learn More

The VD907 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

Learn More

The VD906 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

Learn More

LB180 is an interface circuit board to connect two batteries to a ZLJ24 control panel. The LB180 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB180 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

Learn More

Post with counter-weight and chain latch. for: CAT-X – CAT-X24 - CAT-X110 - CAT-X24110 Learn More

Genovese-type, 9 mm chain for clearances of up to 8 m.

Learn More

The VD961A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

Learn More

The VD963A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

Learn More

24 V DC chain barrier post with gearmotor and built-in control panel. Learn More

230 V AC chain barrier post with gearmotor and built-in control panel.

Learn More

Two-channel 868.35 MHz surface-mounted IP54 12 - 24 V AC - DC receiver for storing up to 50 different users (codes), with TOP, TAM, ATOMO D and TTS coding.

 

Learn More

LB90 is an interface circuit board to connect two batteries to a ZL90 and ZL92 control panels. The LB90 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB90 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

Click here to view LB90 manual

Click here to view LB180 manual

Learn More