Search results for: 'tg:sally530 10 base free than singl telegram good 12v'

ATS-S324   Complete kit for a swing gate weighing up to 400 kg per leaf / max width 3 m

Intensive Duty	CAME Connect	European Standards	Encoder Motor

ATS-S524   Complete kit for a swing gate weighing up to 400 kg per leaf / max width 5 m

Intensive Duty	CAME Connect	European Standards	Encoder Motor

FROG-S  Complete kit for a single swing gate weighing up to 400 kg / max width 3.5m

CAME Connect	European Standards

Complete kit for a single swing gate weighing up to 400 kg / max width 3.5m

Intensive Duty	CAME Connect	European Standards	Encoder Motor

FROGAE-S  Complete kit for a single swing gate weighing up to 400 kg / max width 3.5m

CAME Connect	European Standards	Encoder Motor

A.R22   Vehicle ID receiver

A.R23   Vehicle ID receiver

Make sure you choose the correct number of casements and manual releases so it matches the number of motors that you need.

Use this tool to build a FROG kit of your choice:

-Motor and Control Panel. The panels match the chosen motor.

-Manual release type. Choose from lever, trilobe or custom key.

-Remotes. Choose between 2 button and 4 button, fixed or rolling code.

-Foundation casing. 

-Photocells. 

-Choose whether you need a radio card and/or antenna.

VY350w    Waterproof locking gate magnet

Complete kit for a sliding gate weighing up to 400 kg / max width 10 m

CAME Connect	European Standards

VY500f   Waterproof gate locking magnet

The VD963A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

100m drum of single core rubber loop cable for use with: VD907, VD906, VD955 detectors

Click "Customize" to view all spare part for these products. For additional help, please contact 01491 680500

LB180 is an interface circuit board to connect two batteries to a ZLJ24 control panel. The LB180 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB180 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

The VD907 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

The VD906 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

LB90 is an interface circuit board to connect two batteries to a ZL90 and ZL92 control panels. The LB90 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB90 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

Click here to view LB90 manual

Click here to view LB180 manual

FTL-P   Complete kit for a pair of swing gates weighing up to 200 kg per leaf / max width 2 m

Intensive Duty	CAME Connect	European Standards	Encoder Motor

The VD.CI is designed to accept a plug-in vehicle detector on one side and accept the appropriate wires through the terminal block on the other. This device is designed for detectors that have a solid state output but need a single relay output.

For use with: VD940, VD955, VD913