Search results for: 'fail fitting'

The VD907 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

The VD906 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

Pull-cord release and resetting device to fit on door handle. L = 3 m

The VD955 can be used as either a safety loop or free exit probe detector. It should not be used as a safety loop if used with a Free Exit Probe. 

The VD955 includes a VD.CI Interface board, to work with most gate automation control panels.

• 10-30V ac/dc
• Selectable for full loop or exit sensor
• Selectable fail safe (presence) or fail secure (exit)
• 10 sensitivities
• 4 frequencies
• Contact closure/opening time delay

Automatic barrier with reversible brushless gear motor; painted aluminum wardrobe with set up for fitting accessories. Balancing springs included.

CAME Connect	European Standards

Automatic barrier with irreversible brushless gear motor; galvanized and painted steel cabinet with set up for fitting accessories. Balancing springs included.

CAME Connect	European Standards

Automatic barrier with 24 V DC operator with encoder; galvanised steel and painted cabinet with set up for fitting accessories. Balancing spring included.

CAME Connect	European Standards

Automatic barrier with 24 V DC operator with encoder; galvanised steel and painted cabinet with set up for fitting accessories. Balancing springs included.

CAME Connect	European Standards

Support for fitting DIR-series photocells.

DOC-E Surface fitting safety photocells 20m range ~ Replaced With The DLX30CEP

DLX30CEP - Direct Replacement

DOC-I Flush fitting safety or free exit photocells 20m range. ~ Replaced With The DLX30CIP

DLX30CIP - Direct Replacement

G4000 are issued with the arm clamp for a rectangular arm. This G0405 is required for fitting a 60mm diameter tubular arm.

G6000 are issued with the arm clamp for a rectangular arm. This G0605 is required for fitting a 100mm diameter tubular arm.

The VD961A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

The VD963A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

RIY077 is a tri-lobe manual release key. It is used to open most Came sliding gate motor manual release covers. Once inside the sliding gate release compartment, there is a yellow knob to turn.  It also fits the manual release mechanism on Came FROG underground motor systems fitted with the A4365 release. These keys are sold singly, or in a box of ten. 

Barrier arm for G4000 cabinets, white 60mm diameter. Fits the G0405 arm clamp. The G0461 reflective strips are recommended.

Barrier arm for G6000 cabinets, white 100mm diameter. This arm fits the G0605 arm clamp. The G0461 reflective strips are recommended.

Semi-oval section barrier arm in white aluminum alloy.  A yellow rubber bump strip is fitted in a groove under the arm. Arm length is 4m for 3.75m opening.

LB180 is an interface circuit board to connect two batteries to a ZLJ24 control panel. The LB180 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB180 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.