Search results for: 'gsm 10 gsm a'

Intercom modules for GSM systems.Electronic module with techno-polymer body and 2 call buttons with double, blue or white, namecard backlighting. Slot for on-board micro SIM (micro SIM not included). It can manage up to 1000 telephone numbers and remotely opens the gateway via a telephone ring.

Stand-alone GSM Gateway module for remote control of CAME automated operators with the CAME CONNECT dedicated system (002RSE module included)

GSM Gateway module with built-in radio, for remote control of CAME automated operators with the CAME CONNECT dedicated system (002RSE module included). For controlling up to five slave modules.

A.G64   call activation relay on GSM network

RSLV001 is a GSM gateway for Came control panels. The Came app 'CAMEconnect' can operate and edit control panel operation via SMS received by the RSLZ001.

This set includes the 002RSE serial module that plugs into recent control panels. Check that your control panel is compatible.

CGZP Module 4 rack made of 10 x 10 mm nylon, 1m

Pair of surface mounted synchronized, swiveling, infrared-beam photocells rated at 12 - 24 V AC - DC and battery transmitter. Range: 10 m.

Complete kit for a sliding gate weighing up to 400 kg / max width 10 m

CAME Connect	European Standards

Pair of surface mounted infrared-beam photocells rated at 12 - 24 V AC - DC. Range: 10 m

Operator with 24 V motor, featuring a control board with dip-switch settings, on-board radio decoding, movement and obstruction-detection control for sliding gates weighing up to 400 kg that are up to 10-m long

CAME Connect	European Standards

FA.T80   CoBRA programmable beam

Programmable range photobeam, one side only. Set range on DIP switches, or fully adjustable. 

The VD955 can be used as either a safety loop or free exit probe detector. It should not be used as a safety loop if used with a Free Exit Probe. 

The VD955 includes a VD.CI Interface board, to work with most gate automation control panels.

• 10-30V ac/dc
• Selectable for full loop or exit sensor
• Selectable fail safe (presence) or fail secure (exit)
• 10 sensitivities
• 4 frequencies
• Contact closure/opening time delay

The VD907 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

The VD906 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

LB180 is an interface circuit board to connect two batteries to a ZLJ24 control panel. The LB180 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB180 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

Make sure you choose the correct number of casements and manual releases so it matches the number of motors that you need.

Use this tool to build a FROG kit of your choice:

-Motor and Control Panel. The panels match the chosen motor.

-Manual release type. Choose from lever, trilobe or custom key.

-Remotes. Choose between 2 button and 4 button, fixed or rolling code.

-Foundation casing. 

-Photocells. 

-Choose whether you need a radio card and/or antenna.

LB90 is an interface circuit board to connect two batteries to a ZL90 and ZL92 control panels. The LB90 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB90 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

Click here to view LB90 manual

Click here to view LB180 manual