Search results for: 'tg:echokrys0 top 10 frog-d a singl telegram'

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

Learn More

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

Learn More

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

Learn More

RIY077 is a tri-lobe manual release key. It is used to open most Came sliding gate motor manual release covers. Once inside the sliding gate release compartment, there is a yellow knob to turn.  It also fits the manual release mechanism on Came FROG underground motor systems fitted with the A4365 release. These keys are sold singly, or in a box of ten. 

Learn More

FA.T80   CoBRA programmable beam

Specification: 7 fixed ranges plus full adjustment 10-30V dc   10-24V ac Iq = 65mA, Idetect = 28mA Dimensions 37 x 36 x 108mm Environmental rating – IP65 0.8A @ 30Vdc volt free N/O or N/C Operating temp -10° C to 60° C

Programmable range photobeam, one side only. Set range on DIP switches, or fully adjustable. 

Learn More

FA.T80   CoBRA programmable beam

Specification: 7 fixed ranges plus full adjustment 10-30V dc   10-24V ac Iq = 65mA, Idetect = 28mA Dimensions 37 x 36 x 108mm Environmental rating – IP65 0.8A @ 30Vdc volt free N/O or N/C Operating temp -10° C to 60° C

Programmable range photobeam, one side only. Set range on DIP switches, or fully adjustable. 

Learn More

Pair of surface mounted infrared-beam photocells rated at 12 - 24 V AC - DC. Range: 10 m

Learn More

The VD955 can be used as either a safety loop or free exit probe detector. It should not be used as a safety loop if used with a Free Exit Probe. 

The VD955 includes a VD.CI Interface board, to work with most gate automation control panels.

• 10-30V ac/dc
• Selectable for full loop or exit sensor
• Selectable fail safe (presence) or fail secure (exit)
• 10 sensitivities
• 4 frequencies
• Contact closure/opening time delay

Learn More

The VD907 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

Learn More

The VD906 vehicle loop detector allows "free passage" of vehicles passing overhead. These units are an installer favourite due to their small size and being self setting it's easy to install.

Learn More

VD908  Adjustable mini-loop exit sensor

Specification: 19mm diameter sensor 22m cable length 8-40V dc  or 8-28V ac Iq = 1.6mA, Idetect = 30mA Module size 25 x 39 x 52mm (excl conn) Environmental rating – IP65 1A @ 30Vdc volt free contacts Operating temp -35° C to 74° C

New mini-loop kit with adjustable sensitivity module and new probe 

Learn More

LB180 is an interface circuit board to connect two batteries to a ZLJ24 control panel. The LB180 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB180 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

Learn More

Post with counter-weight and chain latch. for: CAT-X – CAT-X24 - CAT-X110 - CAT-X24110 Learn More

Genovese-type, 9 mm chain for clearances of up to 8 m.

Learn More

24 V DC chain barrier post with gearmotor and built-in control panel. Learn More

230 V AC chain barrier post with gearmotor and built-in control panel.

Learn More

LB90 is an interface circuit board to connect two batteries to a ZL90 and ZL92 control panels. The LB90 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB90 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

Click here to view LB90 manual

Click here to view LB180 manual

Learn More

Opale is the hands-free video intercom with 3.5" and 4.3" LCD touch screen display that guarantees brilliant colors and excellent video quality.

The central blue-backlit dial is for activating the numerous functions available. Particularly suitable for apartment block settings thanks to the possibility of intercom calls and the "Panic" button for emergency calls to the porter.

Learn More

Opale is the hands-free video intercom with 3.5" and 4.3" LCD touch screen display that guarantees brilliant colors and excellent video quality.

The central blue-backlit dial is for activating the numerous functions available. Particularly suitable for apartment block settings thanks to the possibility of intercom calls and the "Panic" button for emergency calls to the porter.

Learn More

Complete kit for a sliding gate weighing up to 3500 kg / max width 17 m

Motor Features: Encoder	Motor Voltage: 230v (Three-Phase)
Max Length: 17m	Max Weight: 3500Kg

 

Three-Phase	European Standards

Learn More