Search results for: 'tg:rebate521 radio time frog track singl frog-a a valutrades'

The VD.CI is designed to accept a plug-in vehicle detector on one side and accept the appropriate wires through the terminal block on the other. This device is designed for detectors that have a solid state output but need a single relay output.

For use with: VD940, VD955, VD913

FA70230CB Irreversible 230 V gearmotor featuring a control board with functions display, on-board radio decoding and hinged transmission arm with C Max. 200 mm for swing gates with with up to 2.3 m leaves that weighs up to 200 kg.

CAME Connect	European Standards

100m drum of single core rubber loop cable for use with: VD907, VD906, VD955 detectors

A.R23   Vehicle ID receiver

FTL-P   Complete kit for a pair of swing gates weighing up to 200 kg per leaf / max width 2 m

Intensive Duty	CAME Connect	European Standards	Encoder Motor

A.K15   Realtime keypad

FTX-P   Complete kit for a pair of swing gates weighing up to 200 kg per leaf / max width 2 m

Intensive Duty	CAME Connect	European Standards	Encoder Motor

FAST70-P  Complete kit for a pair of swing gates weighing up to 200 kg / max width 2.3 m

CAME Connect	European Standards

ZBX7N PCB Replacement PCB

CAME Connect	European Standards	Encoder Motor

The VD961A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

The VD963A, known as the Magna Sensor, is of a new generation of electronic sensors which do the job of a loop detector, except better and more reliably. The Magna sensor recognizes vehicles by the ferrous content of the car. Unlike ordinary loop detectors, the sensor adjusts for most drainage and access covers.

Ethernet Gateway module with built-in radio, with the CAME CONNECT dedicated system (002RSE module included). For controlling up to five slave modules.

VD908  Adjustable mini-loop exit sensor

New mini-loop kit with adjustable sensitivity module and new probe 

433.92 MHz surface-mounted, 12-key radio keypad selector, with blue backlight, 25 savable codes and password to access the programming mode. Settable in Rolling Code or Fixed Code mode.

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

Locking magnet brackets allow two flush surfaces in shear to be locked together by ofsetting the magnet or the armature plate. The brackets are aluminium. The Z bracket is 2 part with ant-slip teeth that is bolted together. The L bracket is a single piece.

LB180 is an interface circuit board to connect two batteries to a ZLJ24 control panel. The LB180 will keep the batteries charged while mains power is applied. It will switch over to the batteries when the mains power fails. 

LB180 takes two 12V batteries. The battery size depends on the anticipated use while running on battery, and the overall time the power is off. In UK, we can expect power outages to be about 10 minutes, but recent storms have seen several days outage.

Operator with 230 - 400 V motor, featuring a control board, on-board radio decoding and mechanical limit-switches for sliding gates weighing up to 3500 kg that are up to 17-m long.

Three-Phase	European Standards

A.G64   call activation relay on GSM network